power grip pedal Power-Grip Pedal Mounting Tape, 1 Meter

power grip pedal Power-Grip Pedal Mounting Tape, 1 MeterIn Stock. 1 Meter Roll Single sided, 1 meter (39. 37 inch) long x 1 inch wide rollapproximately enough for 6 standard sized pedals. Pedal Board Tape Pedalboard Dual Lock and Velcro Alternative For the best Pedalboard Dual Lock and Velcro Alternative, try Power All Power Grip. Simple, yet ingenious, Power Grip pedal board tape mates to itself via rows of tiny mushroom shaped posts that form a much stronger bond than traditional "hook & loop" Velcro

In Stock. 

1-Meter Roll – Single-sided, 1-meter (39.37 inch) long x 1 inch wide roll—approximately enough for 6 standard-sized pedals.

Pedal Board Tape - Pedalboard Dual Lock and Velcro Alternative

For the best Pedalboard Dual Lock and Velcro Alternative, try Power-All Power-Grip®. Simple, yet ingenious, Power-Grip® pedal board tape mates to itself via rows of tiny mushroom-shaped posts that form a much stronger bond than traditional "hook & loop" Velcro fasteners. Just cut to size, apply, and GRIP!

Power-Grip® Is Available In The Following Configurations:

• 5-Meter Roll – Single-sided, 5-meter (Approx. 16 feet) x 1inch wide roll—Enough tape to cover PT-JR & still have some tape left over for your pedal backs.

• 10-Meter Roll – Single-sided, 10-meter (Approx. 33 feet) x 1 inch wide roll—Enough tape to cover PT-3 & still have some tape left over for your pedal backs.
  

POWER-GRIP® is the best Solution for securing your guitar pedals to your pedalboard (No Hype).

INSTRUCTIONS FOR USE

• Mounting surfaces must be free of grease, dirt, loose particles, and moisture.
• Mounting surfaces must be smooth, even and stable.
• Metal surfaces should be cleaned with Acetone prior to mounting.
• Plastic & lacquered surfaces should be cleaned with Lighter Fluid prior to mounting.
• External temperature should be approximately 68° F (20°C) while applying Power-Grip.
• Cut two identically-sized strips of Power-Grip® to the desired length.
• Fasten one strip to the object to be mounted and the other strip to the mounting surface.
• Press tape down firmly and evenly – use of a pressure roller is recommended.
• Use additional pairs of strips as needed for a stronger grip.
• For maximum adhesion, expose the adhesive to hot air (140°-180° F) for at least 2 minutes after mounting.
• Allow at least 24 hours for the Power-Grip® adhesive to set.
• Press the two Power-Grip® strips together and GRIP!

NOTES REGARDING USE

• The Power-Grip® adhesive backing will form a permanent bond over time. Once this occurs, Power-Grip® may damage painted surfaces or leave adhesive residue if removed. Residue can be removed with Acetone or Lighter Fluid.
• Power-Grip® adheres best to smooth surfaces such as coated metal or plastic. It will not adhere well to very rough surfaces such as unfinished wood, etc.
• When in doubt, test adhesion to the surface FIRST using a small piece of Power-Grip®.
• We do not guarantee that Power-Grip® will be suitable for all applications and we do not take responsibility for loss or damage to property due to improper use/mounting of Power-Grip®.

SPECIFICATIONS

TEMPERATURE RANGE: -22° to +200° Fahrenheit (-30° to +93° Celsius)
ADHESIVE: Virtually weather & waterproof. Resistant to aging due to moisture & heat in accordance with Ford Spec. SKM-3G9512-A
DIMENSIONS: 25 mm (1 inch) wide, Approximately 5.4 mm (.2 inch) thick including backing adhesive
STEM COUNT: 42/CM2 (Approx. 100/ Inch2)
PEEL STRENGTH: Approx. 23 N/CM
SHEER STRENTH: Approx. 100 N/CM2
STORAGE: Dry, Dust-free, Dark area w/max. 75°F temp., 50% Humidity Level. 12-months maximum shelf life.